Mini Ultrasonic Micro-Crystal & diamond Microdermabrasion Equipments Machine for home use

Functions Introduction:
1. The Diamond Dermabrasion. (see the preface)
2.Ultrasonic function. Ultrasonic utilizes sonic vibrations; it works
one million times per second (1 MHz). The ultrasonic wave could
stimulate skin tissue and improve permeability of the membrane to
promoted collagen tissue, reduced wrinkle and invisible appeared
fine line, also lift the skin result for younger and healthy look.
Ultrasonic generate frictional heat which accelerate blood
circulation, muscle relaxation, and decompose the cellulite to break
down exceed fat.PH-06 Ultrasound with 2 probes provided
non-surgical lifting. This machine utilizes sonic vibrations to reduce
lines, leaving the skin firm and smooth.
*** Preparation before treatment
1. A consultation included the examination of the skin, a plan for
treatment.
2. Operator should wear vinyl gloves and a facemask.
3. On oily or acne skin, a steamer may be used prior to the
treatment, or a degreasing lotion may be applied prior to the
cleanser.
4. Cleansing the skin with Cleansing gel or water, then wipe off with
cotton pad. Allow the skin to dry.

Preface
The Micro-crystal Dermabrasion was designed by Italian
Florence's Mattioli at first, until now had over 20 years’ history. This
kind of technology only supplies to the dermatology expert and
doctor at first uses, but more and more SPA House & Beauty
Saloon also gradually uses, it was called the best method of
medical beauty. This method successfully has developed in Europe
for several years,
cures patient thousands of examples, and has obtained the
extremely satisfactory effect.
Now we want to introduce the Diamond Dermabrasion, it is a
creative improvement of the Micro-crystal Dermabrasion. The
Diamond Dermabrasion provided a non-surgical skin refinish
procedure, by using sterile diamond heads to abrade or rub off the
top skin layer, then Vacuuming out the particles along with any dirt

and dead skin back up. This procedure removes skin debris,
imperfections, blemishes, wrinkles and unwanted pigmentation on
the skin. Moderate usage of Diamond Dermabrasion, accompany
with skin products that penetrate through top skin layer that reach
the dermis level, helps to replenish natural nutrients, restore cell
activity, and promote skin
health. The results after Micro Dermabrasion treatment is usually a
healthy, glowing, beautiful skin.

Specifications
Voltage: 240V/50/60Hz
220V/50/60Hz
115V/60Hz
Power: 100 VA Fuse: 3A

Operating Instruction for Diamond Dermabrasion
1. Push in the movable ring of copper nozzle at the hand piece, and
pull out the 6x4 size vacuum hose. Then push in the black plastic
ring on the vacuum hose.
2. Put a drop of cream or milk lotion on the vacuum hose nozzle,
push in the movable ring and insert in the vacuum hose to the limit.
3. Insert a cotton swab into the Diamond Head, then tight up the
Diamond Head on the hand piece. Remove the cotton swab after
every treatment.
4. Turn on the power switch.
5. Adjust the vacuum intensity by vacuum Regulator according to
the following reference table, the intensity displays on vacuum
gauge and check with the client for comfort.
Recommended vacuum intensity on treatment area

Use the incline area of Hand piece to contact with the skin
surface. Proceed with a slow sliding motion. Do not place the hand
piece at one spot for too long, doing so will cause harm to the skin.

Adjust the crystal flow rate by the vacuum Regulator slowly from
minimum to maximum. For commonly use, do not set the flow rate
to maximum unless it is of necessity. This is for better comfort
intensity.

Gently stretch the skin with thumb and finger and glide the
Hand-piece 2 to 3 times over the area being treated. Then cross
again in different directions to prevent streaking lines as in the
reference picture. Brush strokes or polishing motions may be used
in different sites.

After treatment, brush off all remaining dead skin with a soft
brush and rinse with damp sponges or damp cool towel.

Allow skin to dry then apply desired skin product.

To clean the Diamond Head, use toothbrush or cotton
swab damped with a little alcohol to wipe off the dirty impurity,
and then use UV light or high temperature for sterilization.