Crystal peel microdermabrasion equipments for skin revitalizer pigment treatment

1.GENERAL INFORMATION

You have purchased the NV-300 Crystal Peeling micro-dermabrasion system, which consists of the following:

·1 Microdermabrador; consisting of a vacuum pump, vacuum monitoring gauge, controls and fittings.

·1 support tower rod

·1 crystal application hand piece with connective tubing

·5 disposable end caps/normal

·3 disposable end caps/nose area

·2 replacement filters

·1 filter funnel

There are NO serviceable parts inside the Microdermabrador enclosure. This enclosure may only be opened by authorized service personnel.

2. Diamond peeling

The Diamond Peel treatment epidermal layers at varying depths in a controlled manner, minimizing skin trauma. It mechanically alters the epidermis and invigorates cell renewal to create a healthy, balances skin surface. It is then possible to improve or eliminate many skin conditions and skin imperfections. The machine also has the hot & cold treatment functions. The cold treatment functions. The cold treatment function is specially designed for claming down the skin after peeling. The skin is sensitive after peeling treatment, so the cold treatment procures is necessary. The hot treatment function is designed for accelerating the absorption of nutrition.

3.INTRODUCTION

The MD001 Crystal Peeling Machine is based on the principles of exfoliation. Different from many other chemical exfoliations available today, it is a dry exfoliation method that is safe to use on many parts of the body including the face area.

Exfoliating can also be understood as the removal of dead skin cells. By using the special crystals we provide, it can help smoothing out wrinkles and fine lines. It is also very beneficial for scars left from wounds or chicken pox. It also helps to unclog pores, stimulate the circulation of the skin, eliminate dead skin cells from the top layer of the skin and improves the skin’s ability to retain moisture. Giving the skin a more youthful and healthy appearance.

However, due to the nature of its treatment, it is very important that this machine is operated by qualified personnel ONLY. Any violations of the above will void the warranty and the operators should be responsible for any damages to the systems and/or client.

4. ASSEMBLY

· Remove the machine from its carton and place it on a flat area free of any liquid.

· Place the hand piece tower rod in the vice on the back left side of the machine and tighten.

· Connect the 2 hoses from the hand piece to the back of the

machine where you will see two fittings.

· Fit the tubes into the appropriate fittings. Push both until they stop. (If they are not fitted securely, the machine will not work correctly). Tug the tubing. It should feel tight.

· Plug the machine into a correct electrical outlet.

· Turn on the power switch. Make sure that the switch lights up and that you have power.

· Remove the hand piece from the holder and check for vacuum pressure by liking. Be careful not to leave the hand piece over any over any one area for more than a couple of seconds.

· You should feel sufficient vacuum pressure and check for wastes entering into the waste bottle.

YOUR CRYSTAL PEELING MACHINE IS NOW READY TO OPERATE

5. PREPARATION

1Prepare cold towels or other likes. The towel should be damp not wet.

2Sterilize hands and put on disposable latex gloves and mouthpiece.

3Remove all jewelry on the client.

4Prepare the skin surface for treatment by first cleansing the area using the prescribed cleanser. You must also cool the skin down by using chilled towels. This will remove any residual cleansing product left on the skin.

5Make sure the skin is dry to the touch.

6Take your hand-piece, making sure it, especially the cap, is

either properly sterilized or replaced.

7Begin treatment.

8Once completed the treatment, you must cool the treated surface of the skin by applying cold towels. Keep doing this until the skin becomes cool to the touch.

9The sin has just experienced an abrasive treatment. It is normal that there may be some redness as well as a warm effect.

10Make sure the clients do not use any other abrasive product on the skin, as it may cause an adverse reaction.

Prior to beginning the Crystal Peel treatment, make sure that the skin is dry to the touch. Depending on the service and skin condition, you may choose to use one pass or many slightly longer timed passes.  Movements should be gentle and rhythmical, but not irritating or uncomfortable. Treatments can be done slowly and in detail-up to 30 minutes FOR THE ENTIRE BODY. A slight reddening after the treatment is a normal reaction.

When working on the face, be sure to follow the pattern of the flow chart (se face flow chart). If working on the body, be sure to use both horizontal and vertical strokes in a “fiber” type action. The strokes may be rapid and repeated over the same area to ensure coverage before moving on to the nest skin area.